Here "configuration" means the assignment of PnP bus-resources (addresses, IRQs, and DMAs). There are two parts to this question for each device. Each part should have the same answer.
Of course the configuration of the device hardware and its driver should be the same (and it normally is). But if things are not working right, there may be a difference. This means the the driver has incorrect information about the actually configuration of the hardware. This spells trouble. If the software you use doesn't adequately tell you what's wrong (or automatically configure it correctly) then you need to investigate how your hardware devices and their drivers are configured. While Linux device drivers should "tell all" in some cases it's not easy to determine what has been set in the hardware.
Another problem is that when you view configuration messages on the screen, it's sometimes not clear whether the reported configuration is that of the device driver, the device hardware, or both. If the device driver is assigned a configuration and then checks the hardware out to see if it's configured the same, then the configuration reported by the driver should be that of both the hardware and the driver.
But some drivers don't do this may accept a configuration that doesn't check out. For example, "setserial" will accept a configuration that doesn't check out (even if you've told it to probe for bus-resources). Thus "setserial" may only be telling you the configuration of the driver and not the hardware.
Some info on configuration may be obtained by reading the messages from the BIOS and Linux that appear on the screen when you first start the computer. These messages often flash by too fast to read but once they stop type Shift-PageUp a few times to scroll back to them. To scroll forward thru them type Shift-PageDown. Typing "dmesg" at any time to the shell prompt will show only the Linux kernel messages and miss some of the most important ones (including ones from the BIOS). The messages from Linux may sometimes only show what the device driver thinks the configuration is, perhaps as told it via an incorrect configuration file.
The BIOS messages will show the actual hardware configuration at that time, but a PnP OS, isapnp, or pci utilities, may change it later. The BIOS messages are displayed first before the ones from Linux. As an alternative to eventually using Shift-PageUp to read them, try freezing them by hitting the "Pause" key. Press any key to resume. But once the messages from Linux start to appear, it's too late to use "Pause" since it will not freeze the messages from Linux.
There may be a programs you can run from the command line (such as "setserial" for serial ports) to determine this. The /proc directory tree is useful. /proc/ioports shows the I/O addresses that the drivers use (or try if it's wrong). They might not be set this way in hardware.
/proc/interrupts shows only interrupts currently in use and many that have been allocated to drivers don't show at all since they're not currently being used. For example, even though your floppy drive has a floppy disk in it and is ready to use, the interrupt for it will not show unless its in use. Again, just because an interrupt shows up here doesn't mean that it exists in the hardware. A clue that it doesn't exist in hardware will be if it shows that 0 interrupts have been issued by this interrupt. Even if it shows some interrupts have been issued, it may mean that this interrupt doesn't exist on that device does exist on some other device which is not in use, but which somehow has issued an interrupt or two. As of kernel 2.2 the /proc tree has changed.
It's easy to find out what bus-resources have been assigned to
devices on the PCI bus with the "lspci" command. For for kernels <:
2.2: /proc/pci will provide some info but it's not too easy
to decipher. For the ISA bus you may try running pnpdump
--dumpregs but it's not a sure thing. The results may be
difficult to decipher. Don't confuse the read-port address which
pnpdump "trys" (and finds something there) with the I/O address
of the found device. They are not the same.
Messages from the BIOS at boot-time tell you how the hardware configuration was then. If you rely on the BIOS for configuring, then it should still be the same. Messages from Linux may be from drivers that have checked to see that the hardware is there (and possibly checked the IRQ and DMA). Of course, if the device works fine, then it's likely configured the same as the driver.